Slots In Altium
For an optimal player experience and site Altium Board Slots performance on any Altium Board Slots device using, we recommend using. The following browsers: Google Chrome and Chrome mobile (latest Altium Board Slots version). You probably set the length of the slot to the width and visa versa. Lets say, based on the image that the width is 1mm and height 4mm. In the slot properties you have to provide the Hole Size as width (1mm) and Length as Height (4mm). The slots are done in a different step than the via drilling. $ endgroup $ – Some Hardware Guy Dec 14 '12 at 3:13 $ begingroup $ Humm ok.I just feel unconfortable with so many different ways to interpret a PCB and repesent a slot.and OSH Park dont show them, unless you put it on the board edge layer I think $ endgroup $ – mFeinstein.
I’ve been working recently on a new top secret project that used multiple slots in the board. Normally I just define them as slotted pads in Altium and the board house deals with it.
Usually I just add a pad that’s defined as a slot with a very small pad in the middle
This time I was using OSH Park, and as it turned out things were not that easy. Their process does not support milled slots in the drill file. Instead slot outlines need to be on the board outline layer, and at least 100 mills wide. After a bit of fiddling, here is how I got there (This assumes you have the part footprint open for editing in PCB Library editor) :
- Draw a closed outline of the slot on the keepout layer, making sure it’s 100mil or wider. This also helps making sure polygon pours stay away.
- Go to Tools> Convert>Create Region from Selected Primitives
- Click on the newly created region and check “Board Cutout” box
Making region a board cutout
- Add “CUTOUT” text inside the cutout on the keepout layer
- Update your parts from the library or place your new parts
- Do placement/routing/design rule checks
- When generating Gerbers, go under Gerber Setup>Layers and make sure to check Plot box near Keep-Out-Layer GKO. This will be your board outline/slots drawing for Oshpark
- Check Gerbers and confirm that GKO layer now contains outlines for the slots:
Section of Keepout layer showing board outline, slots and the text for the fab
- Submit files as usually
Big Disclaimer(s)- I am yet to receive my boards back, so while it appears everything satisfies the specs, I may be completely wrong and the boards will be ruined. I’ll post an update once they come in. The directions are for Altium 13, so if you use 14, some menus may look different. My keepout layer contains board outline as I generate that from board shape by default.
You’ve done your usual excellent job of putting together the PCB schematic. The circuitry is defined and you are ready to go to PCB layout. But this time it’s a little different. Maybe your regular layout resources aren’t available, or perhaps you want to try to do your first layout yourself. Whatever the reason, you are ready to start working on the board side of PCB design, but you’re not sure how to create PCB from schematic Altium Designer.
Fortunately, the next step in Altium Designer is very straightforward. We’ll take a look here at a very simple schematic and see what needs to be done to synchronize it with a brand new PCB design. This simple little design probably won’t be anything like the schematics that you are working on, but the basic steps of data transfer will be the same. Creating a PCB layout from a schematic doesn’t have to be difficult.
How to Convert a Schematic to a PCB Layout in Altium Designer
The process for how to convert a schematic to a PCB layout in Altium Designer follows three simple steps:
Step 1: Preparing to Synchronize the Design
Step 2: Use Schematic Capture to Import Design Data to a PCB
Step 3: Define Your Layer Stack
Step 1 is intended to check your schematic for design rule violations that keep your schematic from being synchronized with your PCB layout. Once your PCB layout is created, this first synchronization step will ensure that any later change in the schematic can be immediately imported into the PCB layout. Step 2 involves using the schematic capture tool to import the board into a blank PCB layout. You'll need to create a new PCB file in your current project, and then use the schematic capture tool to import footprints for your components into your new PCB. In Step 3, you'll define a layer stack for your new PCB. Once you've completed these three steps, you can now start arranging components and routing traces between them.
Can You Import an Existing Schematic File to a New PCB in Altium Designer?
The answer is: Yes! If you have an existing schematic file from another project, and you want to import the schematic to a new PCB, you can simply add the existing schematic file to a new project and follow the three steps above. You won't need to recreate the schematic. If you want to import an existing schematic to a new layout in Altium Designer, be sure to follow some best practices for design reuse. Read more about design reuse in this article.
If you've decided to go the design reuse route and import a schematic to a new PCB, you should make sure you have created libraries for your schematic symbols and footprints for your components. This is especially important if you are using specialty components that are not found in the default set of component libraries in Altium Designer. This is also important if you want to reuse a schematic that was made by another PCB designer.
What Can You Expect in a PCB Layout Editor?
Boards. Circuits. More boards. Traces everywhere, and the occasional flying monkey. Okay, maybe one of those doesn't belong.
In reality, the main thing you need to know to convert a schematic to a PCB layout is that you have access to components and component placement features, as well as traces and trace routing for copper placement. After these initial requirements are met, you’ll want access to printed circuit views and file outputs like PCB footprints, Gerber files and 3D modelling.
In an ideal setting, you'll convert a schematic to a PCB with your schematic capture tool and translate it easily into a finished layout. Then you’ll be able to work through your components, copper setting, ECAD/MCAD design team interventions and purchasing requirements to optimize your PCB design files for manufacturing.
As part of this process, Altium Designer includes several important design that help ensure your create an error-free PCB design from a schematic. You'll be able to quickly check your Altium Designer layout against your design rules and constraints, easily define your layer stack, run simulations of your design, and much more. Altium Designer's integrated design tools are designed to keep your PCB schematic and layout synchronized without using an external program for schematic capture.
Watch this video for a quick demonstration on how to get started with the very basics so you can learn how to create a PCB layout from a schematic in Altium Designer:
Now let's take a look at how to import a schematic to a PCB in Altium Designer:
Step 1: Preparing to Synchronize the Design
The first thing to do is to give your schematic one last look to make sure it's ready for the PCB design to go to layout. This obviously doesn’t mean that you are finished with the PCB design--there will most likely be many changes before you are ready to go out for manufacturing. But you do want to make sure that there aren’t going to be any surprises in layout. Take a look for duplicated circuitry like forgotten copies, parts that should have been deleted, etc.
Now let’s make sure that the schematic checks out OK using the checking process in Altium Designer’s schematic editor. To do this we will want to compile the schematic which will generate all the internal details of the design such as connectivity mapping between components and nets. While the design is being compiled, a host of different checks will be run to verify the schematic to the design rules. So before we compile, let’s take a look at setting these rules up by going to the pulldown menu command; “Project > Project Options”.
The Project Options settings in Altium Designer
In the picture above, you can see a montage of the first four tabs of the options dialog box. First you have the ability to control which error you want to see and how it is reported. Next you can control which pin types are allowed to connect to each other, followed by the third tab which you can use to configure classes of nets and components. Lastly, you can see the tab which shows the settings for the comparator.
This controls how differences between the circuit board schematic and layout are reported and becomes important when you start adding extra design rules to your PCB. For the most part you will not make a lot of changes here, but you can find out details on configuring this in the documentation from Altium Designer.
Now you are ready to compile your PCB document schematic. Go to the “Project > Compile PCB Project…” pulldown menu to engage the compiler. If your design doesn’t have any errors in it, your schematic design session will not return any messages.
In order to show you what an error looks like, we have removed a portion of the net that connects R1 to Q1 in the picture below and run the compiler. As you can see, Altium Designer has reported back to us that net “NetC1_1” only has one pin on it. Once I reconnected that net, the compiler ran without any reported errors as it should.
The compiler report of a design error
Step 2: Use Schematic Capture to Import Design Data to a PCB
Now we are ready to convert a schematic to a PCB layout, but first we need a PCB to transfer too. Right click on the project and select “Add New to Project > PCB” as shown in the picture below. This will create a PCB object in your project tree. Once it is created, right click on it and save it as a new name, in my case I saved it as the same name as my schematic object.
Adding a new PCB object to the project in Altium Designer
With the PCB object created, you will now want to take some time and configure it the way that you want it to be to start your layout work with. First you will want to set up the grid that you need and set the origin of the printed circuit board layout. You will find the menu commands for this in the “View > Grids” pulldown menu and the “Edit > Origin” pulldown menu. You will also want to edit or recreate the board outline so that it is the size and shape that you need. To do this you will first change the board view from 2D to board planning mode in the “View” pulldown menu, and then use the use the appropriate editing commands in the “Design” pulldown menu.
At this point you are ready to transfer the design data from the schematic to PCB design. The schematic capture tool is your 'schematic to PCB converter.' In essence, this will place the components in your schematic inside the PCB editor. They won't be connected with copper traces, but you will see thin lines that link pins on different components together. These lines show you which pins will need to be connected on your board, so pay attention to these when you start arranging your components. These lines match the connections in the PCB schematic and layout. In the PCB editor, go to the “Design > Import Changes From…” pulldown menu command. You will see the “Engineering Change Order” dialog box pop up as shown below.
The Engineering Change Order dialog box in Altium Designer
First click on the “Validate Changes” button on the lower left side of the dialog box. After Altium Designer has finished validating the changes that you are making by synchronizing the schematic data to the PCB, the “Check” column on the right of the dialog box will fill with green checkmarks indicating that those items and any schematic symbols that have successfully validated. Any items that do not validate will have to be investigated and corrected in order to get a fully synchronized design.
Next click the “Execute Changes button. It will take Altium Designer a moment to execute these changes, and you can watch the progress of the changes on the engineering change order dialog box. Once completed, all of the line items will have a green checkmark in the “Done” column as you can see in the picture below.
The Engineering Change Order dialog box after validating and executing the change
Congratulations, you have successfully transferred your design data from the schematic to the board. You can close the engineering change order dialog box now and you will see your components placed next to the board outline in a similar fashion to the picture below.
Schematic data has been successfully transferred to the layout and are ready to be placed
In the image above, you'll notice that the components are in the lower-right corner of the PCB editor window. When you import a schematic to a PCB in Altium Designer, the components will appear pseudo-randomly placed in the PCB editor window. Before you start arranging components around your printed circuit board, it's best to create your layer stack for your board and adjust the board size. You should do this now as your routing strategy may involve the use of vias, and you'll likely be using plane layers for power and ground. Go to the next step to create your layer stack.
Step 3: Define Your Layer Stack
Before you can proceed with layout, there are still some more tasks to do. Thinking about your components and reference designators, gathering your required information on your components and confirming with suppliers is necessary. You will also want to configure the PCB for the physical stackup of board layers, the display of those layers, and the design rules.
The Layer Stack Manager in Altium Designer
Altium Logo
Above, you can see the layer stack manager in Altium Designer. You will find this command in the “Design” pulldown menu. It will allow you to add, copy, delete, and move physical layers in the PCB stackup. You can add layers for signal routing, power planes, and dielectric layers of the board. The layer stack manager also provides you with an impedance calculator as well.
To set up your design rules use the “PCB Rules and Constraints Editor” found in the “Design” pulldown menu. Lastly you will want to configure the display of your PCB layers and objects using the “View Configuration” panel. Below is an example of the view configuration panel’s “Layers & Colors” tab.
The View Configuration panel in Altium Designer
Now that your printed circuit board schematic data has been transferred to the layout, you are ready to start arranging components on your PCB. You can start dragging your components around your new PCB and create your PCB layout. Once you've arranged components, you can start routing traces between them with the routing features in Altium Designer. The View Configuration panel shown above is very useful for expediting your layout process as it allows you to turn on specific layers while routing and arranging components. When placing components, it's best to turn on the surface layer, silk screen layer, mechanicals, and the ground plane layer you'll be using for reference. This helps prevent layout mistakes that can create signal integrity and grounding problems in your PCB. The View Configuration panel is extremely useful as you can toggle different layers on and off so that you can clearly see how you are arranging and routing components.
Altium Designer is the only PCB design software package that is built on a unified design environment, which allows you to easily import a schematic to a PCB layout as we’ve shown here. You can pass design data back and forth between the PCB and schematic; this makes many design tasks simpler and more productive. The easy transfer of design data from schematic to layout is just the start of all the benefits that Altium Designer will give you.
Altium Inc
If you haven’t started using Altium Designer as your go-to PCB design software, take your PCB project to the next level by talking to an expert at Altium Designer.